Chapters Transcript 4 Sensica™ Urine Output System Charging and Cleaning Sometimes it may be convenient to unplug the system and use it on battery power. The sensical urine output system can be powered for a time by a built in battery that will last one hour. The screen will dim when it is unplugged to maximize battery life, it will recharge when plugged into a wall. You can tell that the system is charging by the flashing green light on the base. Once the system is fully charged, this light will be solid green when the monitor is operating on battery backup power, a silent notification will appear as the backup battery life drains. Other alarms and notifications will appear to alert the clinician to plug in the monitor. The system will shut down soon after this alarm if it is not plugged back in when possible power the sensical urine output system with wall supply so that the backup battery is not completely depleted Power off the sensical urine output system if possible, rub a soft cloth in a circular motion to remove smudges, remove any visible debris with a soft cloth soaked in mild detergent between patient. Use use a german Seidel wipe to remove visible debris. Use a new german Seidel wipe to wipe down the display and allowed to remain visibly wet for two minutes to remove dried residue, dampen a lint free cloth with water and wipe down to remove soil from Seems crevices and inclusions. Use a soft bristled brush wrapped in a lint free cloth dampened with detergent. Then use the genocidal wipe to wipe down system and allowed to remain visibly wet for two minutes. Use a soft bristled brush wrapped in a german seidel wipe in Seems crevices and inclusions for the ring connection, carefully wiped down with a german seidel wipe and allowed to remain visibly wet for two minutes. Be careful to avoid the metal connectors on the load cell assembly to prevent damage, remove any visible debris with a soft cloth soaked in mild detergent between patient uses, remove the temperature monitor module from the stand to clean thoroughly dampen a lint free cloth with a mild detergent and wipe down external surfaces of the temperature monitor module, sensor cable and mono plug adapter if applicable to remove soil from Seems crevices and inclusions. Use a soft bristled brush wrapped in a lint free cloth dampened with detergent. Then Use a German seidel wipe to wipe down the system and allowed to remain visibly wet for two minutes. Use a soft bristled brush wrapped in a german seidel wipe in Seems crevices and inclusions to remove dried residue, dampen a lint free cloth with water and wipe down remove sense of a ring from the system. Using a genocidal wipe, remove gross soil from patient ring, allowed the census a ring to remain visibly wet for two minutes After use the census a ring, maybe a potential biohazard handle and dispose in accordance with accepted medical practice and applicable local state and federal law and regulation, the sensical urine output system is indicated to monitor urine output and core bladder temperature when connected to a temperature sensing fully catheter temperature sensing. Foley catheters are intended for use in conjunction with the sensical urine output system and other compatible 400 series temperature sensing monitors. To provide a measure of core bladder temperature, please consult product label inserts and instructions for use for any indications, contraindications, hazards warnings, cautions and directions for use warnings. The B. D. Sensical urine output system is designed to be used with any barred foley catheter and urological disposables connected to any standard urine drainage bag. 2000 or 2500 mL. With or without a urine meter ensure that the urine drainage bag hanging on the BD sensical ring is always below the level of the patient's bladder to maintain continuous gravity flow of urine into the collection bag. Precaution during system startup and in general practice plugged the beauty sensical urine output system into a wall power supply whenever possible. The system screen will dim when the system is unplugged. To maximize battery life. After using the system on battery backup, plug it back into the wall power supply for recharging and to avoid system shutdown due to a drained battery. This information pertains to s. c. c. s. 1002. If using SCCC. S 1001, please refer to the instructions for use for more information. For more information on product training and education programs. Contact barred dot E. D. U. At B. D. Dot com Created by
